Discussion about ZX80 / ZX81 Software
-
mrtinb
- Posts: 2004
- Joined: Fri Nov 06, 2015 5:44 pm
- Location: Denmark
-
Contact:
Post
by mrtinb »
1024MAK wrote: ↑Sun Aug 11, 2019 3:15 pm
Hang on! This is a MT07-02 Memotech Centronics Interface!
Yes, they look very much like the Centronics I/F in this album
https://secure.flickr.com/photos/x0r4/a ... 402381338/
Edit: Looking at these pictures there seem to be both a MT07-01 and MT07-02 Centronics I/F.
-
Moggy
- Posts: 3494
- Joined: Wed Jun 18, 2008 2:00 pm
Post
by Moggy »
CRAP I have confused this topic with another my apologies!!
MemoTEXT pics to follow.
TRY AGAIN!!
EPROMS 2716/2732
-
Attachments
-

-

-

???????????????????????????PIINKEY$?????RND????????????????????????????????????????????????????????PI????????
-
mrtinb
- Posts: 2004
- Joined: Fri Nov 06, 2015 5:44 pm
- Location: Denmark
-
Contact:
Post
by mrtinb »
-
1024MAK
- Posts: 5529
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
-
Contact:
Post
by 1024MAK »
IC1 PAL14L4-2CN Programmable Logic chip
IC2 82S123N 32 x 8 bit (256 bit) PROM
IC3 2716 EPROM (2K bytes)
IC4 2732 EPROM (4K bytes)
IC5 74LS00 Quad 2-input NAND gates
Mark
-
XavSnap
- Posts: 2195
- Joined: Sat May 10, 2008 4:23 pm
- Location: 'Zx81 France' Fb group.
-
Contact:
Post
by XavSnap »
[private message]
Last edited by
XavSnap on Sun Jul 19, 2020 9:19 am, edited 1 time in total.
Xavier ...on the Facebook groupe : "Zx81 France"(fr)
-
XavSnap
- Posts: 2195
- Joined: Sat May 10, 2008 4:23 pm
- Location: 'Zx81 France' Fb group.
-
Contact:
Post
by XavSnap »
[private message]
Last edited by
XavSnap on Sun Jul 19, 2020 9:20 am, edited 1 time in total.
Xavier ...on the Facebook groupe : "Zx81 France"(fr)
-
1024MAK
- Posts: 5529
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
-
Contact:
Post
by 1024MAK »
XavSnap wrote: ↑Sun Aug 11, 2019 9:41 pm
Looking at the board, I’m guessing that the 34 Way pin header is a parallel (Centronics like) port.
Yes, but the OCTAL TRANSPARENT LATCH WITH 3-STATE OUTPUTS… is made to send datas to printer, not retrieve datas !
That’s what I meant
Mark
-
XavSnap
- Posts: 2195
- Joined: Sat May 10, 2008 4:23 pm
- Location: 'Zx81 France' Fb group.
-
Contact:
Post
by XavSnap »
[private message]
Last edited by
XavSnap on Sun Jul 19, 2020 9:20 am, edited 1 time in total.
Xavier ...on the Facebook groupe : "Zx81 France"(fr)
-
mrtinb
- Posts: 2004
- Joined: Fri Nov 06, 2015 5:44 pm
- Location: Denmark
-
Contact:
Post
by mrtinb »
-
mrtinb
- Posts: 2004
- Joined: Fri Nov 06, 2015 5:44 pm
- Location: Denmark
-
Contact:
Post
by mrtinb »
HALT!
No need to read the EPROMs.
Fred Nachbaur has an article in SyncWare News Vol. 2 Num. 2 Page 6-8.
This article describes how to read out Memotext to tape, and load it in RAM at 8k.
It even decribes how to add extra commands like QIT to quit the program.
https://archive.org/stream/SyncWareNews ... ews%20v2n2
Last edited by
mrtinb on Mon Aug 12, 2019 3:24 pm, edited 1 time in total.