128 2a problems
128 2a problems
Hi all
So I finally got my first Spectrum. It's only been 40 years since I first saw one but I don't like to rush into new technology. The bleeding edge is where you get cut.
Anyway. I picked up a boxed and clean 128 +2a (black case) which turned out to have a dead PSU. With my brothers help we've got a cisco router PSU wired up to work. I boot to the main screen and have tried loading a few tapes. Lots of noise of course but nothing loaded. One tape reached the end, another the screen stopped flashing.
I plugged a joystick in (it was the Sinclair one bundled originally) but in both ports is causes a buzzing sound until a direction or fire are pressed. Not done any work on that one yet.
The cursors don't work. I pulled the membrane out and cleaned with electrical contact cleaner and it worked briefly. Are these replaceable?
No doubt there will be more issues but sort of fixing them as I find them.
Any suggestions what/where to check for the above?
Once it's working I'll probably get a divmmc and not bother with the tapes.
Thanks
Paul
So I finally got my first Spectrum. It's only been 40 years since I first saw one but I don't like to rush into new technology. The bleeding edge is where you get cut.
Anyway. I picked up a boxed and clean 128 +2a (black case) which turned out to have a dead PSU. With my brothers help we've got a cisco router PSU wired up to work. I boot to the main screen and have tried loading a few tapes. Lots of noise of course but nothing loaded. One tape reached the end, another the screen stopped flashing.
I plugged a joystick in (it was the Sinclair one bundled originally) but in both ports is causes a buzzing sound until a direction or fire are pressed. Not done any work on that one yet.
The cursors don't work. I pulled the membrane out and cleaned with electrical contact cleaner and it worked briefly. Are these replaceable?
No doubt there will be more issues but sort of fixing them as I find them.
Any suggestions what/where to check for the above?
Once it's working I'll probably get a divmmc and not bother with the tapes.
Thanks
Paul
- 1024MAK
- Posts: 5103
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: 128 2a problems
Hi Paul
I’ve moved your thread into the Sinclair ZX Spectrum Hardware area.
A blown transistor is the most common cause of the +2A PSUs to fail. It’s a relatively simple repair (I also recommend the smaller control transistor is renewed at the same time).
I assume you were loading via the built-in cassette deck? May be a good idea to clean the head.
The joystick ports on the Amstrad produced machines, including the +2A that you have (which probably is actually a +2B board in a +2A case) have a non-standard pin-out. How many plugs and what colour are they on the joystick that you have? Of is it actually branded as Sinclair?
It’s not a good idea to clean the membrane with any kind of solvent or electrical contact cleaner. Just wipe each side with soapy water, then wipe again with clean water. Clean the other keyboard plastic parts in warm soapy water, and rinse with clean water. Then allow to dry completely before refitting. The membranes in these machines are fairly reliable, so new replacements are hard to find.
Where spare parts are available, they often are available to buy at Sell My Retro.
Mark
I’ve moved your thread into the Sinclair ZX Spectrum Hardware area.
A blown transistor is the most common cause of the +2A PSUs to fail. It’s a relatively simple repair (I also recommend the smaller control transistor is renewed at the same time).
I assume you were loading via the built-in cassette deck? May be a good idea to clean the head.
The joystick ports on the Amstrad produced machines, including the +2A that you have (which probably is actually a +2B board in a +2A case) have a non-standard pin-out. How many plugs and what colour are they on the joystick that you have? Of is it actually branded as Sinclair?
It’s not a good idea to clean the membrane with any kind of solvent or electrical contact cleaner. Just wipe each side with soapy water, then wipe again with clean water. Clean the other keyboard plastic parts in warm soapy water, and rinse with clean water. Then allow to dry completely before refitting. The membranes in these machines are fairly reliable, so new replacements are hard to find.
Where spare parts are available, they often are available to buy at Sell My Retro.
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert ![Exclamation :!:](./images/smilies/icon_exclaim.gif)
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
![Exclamation :!:](./images/smilies/icon_exclaim.gif)
![Exclamation :!:](./images/smilies/icon_exclaim.gif)
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
![Exclamation :!:](./images/smilies/icon_exclaim.gif)
Looking forward to summer later in the year.
Re: 128 2a problems
Thanks Mark,
It was only when it booted I got the menu stating it was a 2a. The board is an issue 2.
The joystick I used was the Sinclair one that was included in the pack when new. It's the Action Pack with light gun.
Yes I was using the inbuilt tape drive. I thought the 3.5 socket was an output only, not an input or I'd use that. I didn't clean the heads so will get some IPA on that.
Thanks for the note on the membrane. I'll open up and clean with some mild soap then and try that.
I'll update as this develops but as always input appreciated.
Paul
It was only when it booted I got the menu stating it was a 2a. The board is an issue 2.
The joystick I used was the Sinclair one that was included in the pack when new. It's the Action Pack with light gun.
Yes I was using the inbuilt tape drive. I thought the 3.5 socket was an output only, not an input or I'd use that. I didn't clean the heads so will get some IPA on that.
Thanks for the note on the membrane. I'll open up and clean with some mild soap then and try that.
I'll update as this develops but as always input appreciated.
Paul
Re: 128 2a problems
Oh and I forgot to ask, is there any sort of POST diagnostic in a +2a?
Re: 128 2a problems
Yes there is. See there https://www.dataserve-retro.co.uk/conte ... k/d66.html and scroll down to the bottom.
Claudius
----------
----------
Re: 128 2a problems
Thanks I'll try that tonight as well as open up the joystick to see if there is a short / fault there making the buzz/hum when plugged in.
Re: 128 2a problems
Ok, tonight's update.
I cleaner the tape head last night and that now loads games. Fixed.
Cleaned the membrane and keyboard all seems to work although playing Knightmare the controls were all over the shop. Do things like the Graphic or Extend mode keys affect in game controls? Work in progress...
Opened the joystick and suspect the down pad on the PCB dead and possibly a short on one fire button registering as constantly pressed hence the sound I was hearing. My error, it wasn't a buzz but the sound of a key/button being held down.
More work to follow.
I cleaner the tape head last night and that now loads games. Fixed.
Cleaned the membrane and keyboard all seems to work although playing Knightmare the controls were all over the shop. Do things like the Graphic or Extend mode keys affect in game controls? Work in progress...
Opened the joystick and suspect the down pad on the PCB dead and possibly a short on one fire button registering as constantly pressed hence the sound I was hearing. My error, it wasn't a buzz but the sound of a key/button being held down.
More work to follow.
- 1024MAK
- Posts: 5103
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: 128 2a problems
Yes. Funny enough, I wrote a long post about the “extra” keys in a post over on Spectrum Computing that you may want to read.
Yeah, those ‘Sinclair’ branded joysticks were infamous for their poor quality, even back in the day...
It is possible to buy adaptor leads, then you can use ‘Atari’ standard wired joysticks.
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert ![Exclamation :!:](./images/smilies/icon_exclaim.gif)
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
![Exclamation :!:](./images/smilies/icon_exclaim.gif)
![Exclamation :!:](./images/smilies/icon_exclaim.gif)
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
![Exclamation :!:](./images/smilies/icon_exclaim.gif)
Looking forward to summer later in the year.