TS 1000 artifacts after warming up
TS 1000 artifacts after warming up
So I bought a TS 1000 and found the ULA was dead. I did the composite mod and the internal 16K memory upgrade. I bought Andy's ULA and everything worked! (for a little while). The first time I used it I had it on for about an hour and had it running a math problem. It worked great. Later though it started to show signs of a problem. After being off for several hours (nice and cool) I would plug it in and after about a minute it starts to get wavy artifacts. You can still the the 'K' at times. After a little more time the screen goes completely bonkers. Almost like the screen you see when loading or saving.
On the oscilloscope, the output shows a nice and steady signal with the back porch. When it starts having artifacts the signal is still there but it is jumping all over the place. (see video)
So any ideas why the signal starts jumping when it gets a little warm?
On the oscilloscope, the output shows a nice and steady signal with the back porch. When it starts having artifacts the signal is still there but it is jumping all over the place. (see video)
So any ideas why the signal starts jumping when it gets a little warm?
Last edited by embpic on Sat May 04, 2019 2:37 pm, edited 1 time in total.
- 1024MAK
- Posts: 5118
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: TS 1000 artifacts after warming up
How much ripple is on the 9V PSU output and what voltage do you get?
Same question, but on the +5V rail.
Both can be tested on the pins of the 7805 voltage regulator, just be careful not to short anything out.
Mark
Same question, but on the +5V rail.
Both can be tested on the pins of the 7805 voltage regulator, just be careful not to short anything out.
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
Re: TS 1000 artifacts after warming up
Here are the videos.
- Attachments
-
- signal.m4v
- (1.31 MiB) Downloaded 132 times
-
- zx81.m4v
- (1.66 MiB) Downloaded 138 times
Re: TS 1000 artifacts after warming up
PSU output is 11.3V
The 5V rail is right at 5V. Both Voltages have no ripples. Both are pretty clean.
Re: TS 1000 artifacts after warming up
Here is another picture. You can see the video signal spacing is random. On one scan line you can see where the 'K' is generated and then another scan line doesn't finish before it starts again.
At least that is what I (as a noob) see.
Sean
At least that is what I (as a noob) see.
Sean
-
- Posts: 2169
- Joined: Sat Nov 26, 2016 2:42 am
Re: TS 1000 artifacts after warming up
Do you have other chips from other zeddies you can try in it? It would probably be worth being certain the Z80 and ROM are ok.
ZX80
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
ZX81 iss 1 (bugged ROM, kludge fix, normal, rebuilt)
TS 1000 iss 3, ZXPand AY and +, ZX8-CCB, ZX-KDLX & ChromaSCART
Tatung 81 + Wespi
TS 1500 & 2000
Spectrum 16k (iss 1 s/n 862)
Spectrum 48ks plus a DIVMMC future and SPECTRA
Re: TS 1000 artifacts after warming up
Yup. I tried that already. Same result.Lardo Boffin wrote: ↑Sat May 04, 2019 2:49 pm Do you have other chips from other zeddies you can try in it? It would probably be worth being certain the Z80 and ROM are ok.
Something new however. I just left it on and and now I am getting long periods (20-40 seconds) of normal operation and then back to the artifacts.
It is definitely going crazy when the scan resets before it is completed.
Re: TS 1000 artifacts after warming up
Check, if the oscillator frequency (at Pin 6 CPU) is stable at 6.5MHz. Could you replace the ULA?
Re: TS 1000 artifacts after warming up
Its is nice and steady at 3.25mhz. Should it be as 6.5mhz?
Neither of my original ULAs work (210 and 184). I have Andy's ULA installed.
- 1024MAK
- Posts: 5118
- Joined: Mon Sep 26, 2011 10:56 am
- Location: Looking forward to summer in Somerset, UK...
Re: TS 1000 artifacts after warming up
The Sinclair ULA uses a 6.5MHz ceramic resonator. Inside the ULA this frequency is divided by two to give the 3.25MHz CPU frequency. IIRC Andy’s replacement ULA module uses it’s own crystal and ignores the 6.5MHz ceramic resonator on the main board.
Have you tried another monitor / TV ?
The video output from a ZX81 is not compliant with broadcast video standards and it is possible that your monitor just does not like the video output from a ZX81.
Also, I assume this is a U.S.A. spec board. Is resistor R30 fitted?
Also, if you have a working keyboard membrane, try switching to FAST mode (the FAST keyword is in the ‘F’ key, so hold Shift then press ‘F’).
Mark
Have you tried another monitor / TV ?
The video output from a ZX81 is not compliant with broadcast video standards and it is possible that your monitor just does not like the video output from a ZX81.
Also, I assume this is a U.S.A. spec board. Is resistor R30 fitted?
Also, if you have a working keyboard membrane, try switching to FAST mode (the FAST keyword is in the ‘F’ key, so hold Shift then press ‘F’).
Mark
ZX81 Variations
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.
ZX81 Chip Pin-outs
ZX81 Video Transistor Buffer Amp
Standby alert
There are four lights!
Step up to red alert. Sir, are you absolutely sure? It does mean changing the bulb
Looking forward to summer later in the year.