Converting TAP to WAV files for Spectrum

Post Reply
egrabczewski
Posts: 4
Joined: Thu Mar 14, 2019 11:11 am

Converting TAP to WAV files for Spectrum

Post by egrabczewski » Thu Mar 14, 2019 1:49 pm

I've recently built the zxtap2wav command for various systems (Windows, Linux, Mac) which you can download here:

http://thesoundmanifesto.co.uk/downloads/zxtap2wav.zip

It's password protected so just message me for the password.

I've tried it on ZX Spectrum LOGO and recorded a cassette tape using the resulting audio WAV file (using Audition). The cassette load perfectly on an original ZX Spectum with rubber keyboard but wouldn't load on my ZX Spectrum +3.

User avatar
Andy Rea
Posts: 1546
Joined: Fri May 09, 2008 2:48 pm
Location: notts UK

Re: Converting TAP to WAV files for Spectrum

Post by Andy Rea » Thu Mar 14, 2019 5:54 pm

is it possible that that particular program does not work on a +3 there are some incompatiblities.

regards Andy
6 x ZX81, 1 x TS1500 , 1 x +3e, 1 x timex 2040 printer, 1 x timex 2020 cassette deck, siclair printer and some spectrum

User avatar
1024MAK
Posts: 2538
Joined: Mon Sep 26, 2011 10:56 am
Location: Looking forward to summer in Somerset, UK...

Re: Converting TAP to WAV files for Spectrum

Post by 1024MAK » Fri Mar 15, 2019 12:34 pm

The ZX Spectrum +3 may need an audio source with a louder signal. Often an amplifier is needed.

Also note that although the socket on the +3 is a two channel “stereo’ 3.5mm type, one channel is tape/sound out, the other channel being the input from the cassette tape.

So either a special cable is needed, or use a 3.5mm “stereo” jack socket to two mono connectors (e.g. Phono/RCA), then another suitable cable to your audio source (PC for example). With only one of the mono connectors linking the two being connected.

Mark

McKlaud
Posts: 255
Joined: Tue Dec 19, 2017 10:02 pm
Location: St Albans, UK

Re: Converting TAP to WAV files for Spectrum

Post by McKlaud » Fri Mar 15, 2019 5:23 pm

@Andy Rea: yes, some software would not work on +3 series due to lack of the floating bus in this model.
Claudius
----------

User avatar
1024MAK
Posts: 2538
Joined: Mon Sep 26, 2011 10:56 am
Location: Looking forward to summer in Somerset, UK...

Re: Converting TAP to WAV files for Spectrum

Post by 1024MAK » Fri Mar 15, 2019 7:34 pm

McKlaud wrote:
Fri Mar 15, 2019 5:23 pm
@Andy Rea: yes, some software would not work on +3 series due to lack of the floating bus in this model.
There is a bodge fix for this problem. But the lack of a “floating bus” will not prevent loading.

Mark

egrabczewski
Posts: 4
Joined: Thu Mar 14, 2019 11:11 am

Re: Converting TAP to WAV files for Spectrum

Post by egrabczewski » Fri Mar 22, 2019 9:19 pm

I was having problems loading micro-PROLOG and Spectrum FORTH recently but I've noticed that either increasing the volume (PROLOG) or reading the instructions in the manual (LOGO) where I should have been typing LOAD "" CODE and not just LOAD "" , solved my problems. I think I also have a dodgy audio connection which needs a bit of wiggling to get it to work.

By the way, I've just found another tool called "castool" that converts TZX files to WAV as well as a host of other conversions. I'll put up a post about it. So far I've only downloaded the macOS version of the code (see source website: https://www.mamedev.org/). Here's a list of all the conversions it can do!!:

https://docs.mamedev.org/tools/castool. ... l-for-mame

Sinclairs-great
Posts: 11
Joined: Wed Nov 06, 2019 1:37 am

Re: Converting TAP to WAV files for Spectrum

Post by Sinclairs-great » Wed Nov 06, 2019 10:43 pm

Hello
I see your good at programmes or files . I have a Sinclair zx spectrum vega could you tell me how to download zx spectrum games from sites on the net to a micro sd card to play on the vega .I mean do I need a zip file to open them . I use a android . Do I need a bigger pc. I download them but when I try to open them it says " can't open file" . Do I have to buy a certain zip file or what do I buy ?

Post Reply